Important: This article is general information for education only. It does not recommend any project or builder. Verify project details, including carpet area, on your state RERA portal and in the registered agreement for sale, and take independent legal advice before paying.


Two flats near the same tech park are both advertised as “1,250 sq ft” at similar prices. One feels noticeably larger when you walk through it. The reason is usually not the architect’s skill but the way area is measured. Brochures and sales conversations often still talk in super built-up area, while the Real Estate (Regulation and Development) Act, 2016 (RERA) requires flats in registered projects to be sold on the basis of carpet area. Knowing the difference lets you compare projects on what you can actually use.

This guide explains the three common terms, what RERA’s definition includes and excludes, and a step-by-step method to compare prices per usable square foot.

The three measurements

TermGenerally includesLegal status
Carpet area (RERA)Net usable floor area inside the flat, including internal partition wallsDefined in Section 2(k) of RERA; basis for sale in registered projects
Built-up areaCarpet area plus external walls, shafts and often balconiesIndustry term; no single statutory definition
Super built-up areaBuilt-up area plus a share of common areas such as lobbies, staircases, lift wells and sometimes clubhouseIndustry term; methods vary between builders

What RERA’s carpet area definition says

Section 2(k) of RERA defines carpet area as the net usable floor area of an apartment, excluding the area covered by the external walls, areas under services shafts, exclusive balcony or verandah area and exclusive open terrace area, but including the area covered by the internal partition walls of the apartment.

Three practical points follow from this:

  • Balconies and terraces are listed separately. An exclusive balcony or open terrace does not count in carpet area, but the agreement should state its size separately.
  • Internal walls are included. The carpet area is slightly larger than the floor area you could literally cover with a carpet.
  • Common areas are not part of it. Lobbies, corridors and amenities are common property of the association, not part of your apartment’s carpet area.

Promoters must disclose apartment carpet areas when registering a project, and the agreement for sale should state the carpet area. Some state authorities have issued their own regulations reinforcing sale on carpet area; Haryana’s RERA, for example, published regulations on sale of apartments on the basis of carpet area. Builders may still mention super built-up figures for reference, but the price should be traceable to carpet area.

A worked example: same headline, different flats

Neha and Rahul, both software engineers, are comparing two 2 BHK flats in Hyderabad, each marketed as “1,250 sq ft super built-up” at ₹9,000 per sq ft, so ₹1,12,50,000 each before other charges. They ask both builders for the RERA carpet area and balcony area.

ItemProject AProject B
Super built-up area (sq ft)1,2501,250
RERA carpet area (sq ft)860940
Exclusive balcony (sq ft)7060
Base price (₹)1,12,50,0001,12,50,000
Price per sq ft of carpet area (₹)13,08111,968
Loading over carpet area45.3%33.0%

Project B gives 80 sq ft more usable space for the same money, which works out to about ₹1,113 less per sq ft of carpet area. Loading is calculated as (super built-up − carpet) ÷ carpet: for A, (1,250 − 860) ÷ 860 = 45.3%; for B, (1,250 − 940) ÷ 940 = 33.0%. Higher loading is not automatically bad—a project with large amenities will have more common area—but buyers should know what they are paying for.

Step-by-step: comparing flats on usable area

  1. Find the project on your state RERA portal using the registration number printed on the advertisement.
  2. Download the carpet area details for the unit type, and the approved floor plans if available.
  3. Ask the builder for a cost sheet that states carpet area, balcony area and the total price.
  4. Divide the all-in price (base price plus mandatory charges such as car parking or club membership, if compulsory) by the carpet area.
  5. Compare that figure across projects, adjusting for amenities, location and construction stage.
  6. Check that the draft agreement for sale states the carpet area and the balcony area separately.
  7. At possession, measure the flat or have it measured, and compare with the agreement.

What if the delivered carpet area is smaller?

Small variations can occur during construction. The agreement for sale, often based on a model agreement notified by the state, usually sets out how variations in carpet area are handled—for example, refunding excess amounts collected if the area is reduced beyond a tolerance, or charging for an increase within a limit. Read this clause before signing. If the builder delivers materially less than agreed and does not adjust the price, you can raise a complaint with the state RERA authority. Our guide on RERA rights when possession is delayed explains the complaint process in general terms.

Why this matters for home loans and costs

  • Loan amount: lenders fund a percentage of the property’s value based on their own valuation, which may differ from the builder’s price per sq ft.
  • Maintenance: monthly maintenance is often charged per sq ft of super built-up area, so a high loading raises your running costs too.
  • Resale: buyers increasingly ask for carpet area, so a high-loading flat may be harder to price at resale.
  • Furniture and work-from-home space: for IT couples who both work from home, the usable area decides whether a second bedroom can double as a study.

For the full due-diligence process on new projects, see our guide to RERA checks before booking an under-construction flat.

Resale flats and older buildings

For flats in buildings completed before RERA, or resale flats, the original sale deed may state built-up or super built-up area. Ask the seller for approved plans and measure the flat yourself. When comparing a resale flat with a new RERA-registered flat, convert both to carpet area to make a fair comparison.

Common mistakes

  • Comparing projects by headline super built-up figures.
  • Assuming the balcony is part of carpet area.
  • Ignoring compulsory charges when calculating price per sq ft.
  • Not checking the area variation clause in the agreement.
  • Skipping measurement at possession.

FAQ

Can a builder still quote super built-up area?
Builders may mention it, but in RERA-registered projects the sale should be on carpet area, and the agreement should state the carpet area. If only super built-up area is offered, ask for the carpet area in writing.

Is a lower carpet-to-super built-up ratio always a bad deal?
Not necessarily. Large amenities and wide corridors add to common area. Decide whether you value those amenities enough to pay for them.

How do I measure carpet area myself?
Measure each room wall to wall, add the area under internal partition walls, and exclude balconies, external walls and shafts. A professional surveyor can do this more accurately for a fee.

Sources


Last reviewed: 2 November 2026. This article is general information, not legal or financial advice, and does not recommend any project or builder. Verify all project details on your state RERA portal.

Leave a Reply

Trending